There are a couple of options when it comes to descaling your Keurig. This should be done routinely every three to six months, depending on how often you’re using your Keurig. To fix this problem, you’ll need to descale your Keurig. Descaling is sometimes done by the Keurig machine itself, but can also be done by using a homemade solution. Scale from tap water can clog up your water pump, interrupting your water flow. What is Descaling?ĭescaling is the process of cleaning your Keurig of this scale, that’s typically made of water deposits and calcium. This build-up inhibits the brewing process, and your Keurig will need to be descaled. These minerals that build up usually come from tap water as your primary water source to brew coffee. It is a common cause of problems with Keurig that inhibit its ability to complete the brewing process. Over time, your Keurig will fall victim to a build-up of mineral deposits. Remove the water reservoir and ensure that the water magnet is floating in the little slot that’s there to support it rather than floating freely – this will realign the magnet and restore your brewer to operable status! Your Keurig Needs Descaling To do this, you’ll need to turn off the Keurig and unplug the Keurig from the wall. How to Fix Water Magnet Alignmentįixing a misaligned magnet issue can only be done by removing the water reservoir. Sometimes, this magnet can become misaligned, which will cause an error in the machine water reservoir sensor, causing it to shut off and stop pumping water. The water magnet is a magnet that floats where there is sufficient water in the reservoir to begin brewing. The water magnet is what helps the machine determine whether or not there is sufficient water in the water tank to begin brewing. The water magnet alignment is offĪnother possibility for why your Keurig coffee machine continues to stop brewing and shut off is that the water magnet alignment is off. This is an easy fix that you can do yourself without having to call Keurig support. Replacing these is a simple task of finding the appropriate gasket from either Keurig or Amazon – it needs to be compatible with your machine – and then replacing the gasket. If either one of these needs replacing, you’ve likely found the source of your problem. The same is true of the bottom needle, known as the exit needle. If it is bent or broken, you’ll need to replace the needle gasket with one that is compatible with your Keurig. If it is, then it’s fine, and your problem lies elsewhere. Before you load a fresh k cup in and hit the brew button, check the entrance needle to see if it’s pointing straight downward. If you’re finding that your coffee maker isn’t working when you hit brew, this might be why. Usually, if you tried to make coffee with a cup that was too tall for the Keurig machine but shoved it in there anyway, causing damage to the needle.īroken or bent needles can occur in either the top entrance needle (where the hot water flows through into the k cup holder) or in the exit needle, where the finished coffee product flows into your morning cup. Broken or bent needles are less commonly a problem, as the needles would require quite a bit of force to break, but it does happen. Broken or Bent Needlesīroken or bent needles are another reason why your Keurig keeps shutting off while brewing. You should also wash out the pod holder with hot water. You won’t be able to poke through the brew head but start gently wiggling the paper clip around, this will loosen up the debris and gunk from inside the pod holder. This may take a bit of wiggling, but once it’s free, you can access the needle. Next, you’ll want to remove the funnel from your Keurig coffee machine. Next, you’ll want to remove the k cup holder from the Keurig machine. First, you’ll want to turn off your Keurig and unplug it from the wall. One of the easiest ways to clean your exit needles is to use a paperclip. Various gunk can build up around your exit needles, causing them to become clogged.Ĭleaning your Keurig’s needle is something that needs to be done regularly – once a week is a good timeline. Sometimes, these needles can become clogged with various debris from your k-cups and other coffee debris. The brewing process can begin once you’ve hit brew and where the wakey-wakey juice comes from. They’re the thing that spurts out the coffee when you hit brew. The exit needles are one of the most important parts of your Keurig machines.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |